万兆单模单纤20KM 1270~1330波长

讯艾拓 XAT-WW20-127/133 光模块 Bi-directional 10Gb/s (SFP+) transceivers are compliant with the current SFP+ Multi-Source Agreement (MSA) Specification. They comply with 10Gbase-LR/LW Ethernet SONET OC-192 / SDH and 10G Fibre Channel

产品概述

一、产品概述：
讯艾拓 XAT-WW20-127/133 光模块 Bi-directional 10Gb/s (SFP+) transceivers are compliant with the current SFP+ Multi-Source Agreement (MSA) Specification. They comply with 10GBASE-LR/LW Ethernet, SONET OC-192 / SDH and 10G Fibre Channel 1200-SM-LL-L. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the SFP+ MSA.

二、产品特点：

Features:

² Supports 9.95Gb/s to 11.3Gb/s bit rates

² Hot-pluggable SFP+ footprint

² Single LC for Bi-directional Transmission

² Maximum link length of 20km

² Built-in 1270/1330 WDM Filter

² Uncooled 1270nm or 1330nm CWDM DFB Laser.

² Power dissipation <1.5W

² No Reference Clock required

² Built-in digital diagnostic functions

² Temperature range 0°C to 70°C

² Very low EMI and excellent ESD protection

² RoHS Compliant Part

Applications:

² 10GBASE-LR/LW Ethernet

² SONET OC-192 / SDH

10G Fibre Channel

三、产品参数：
Absolute Maximum Ratings：

Parameter	Symbol	Min.	Typical	Max.	Unit
Storage Temperature	T_S	-40		+85	°C
Supply Voltage	V_CCT, R	-0.5		4	V
Relative Humidity	RH	0		85	%

Recommended Operating Environment:

Parameter	Symbol	Min.	Typical	Max.	Unit
Case operating Temperature	T_C	-5		+70	°C
Supply Voltage	V_{CCT, R}	+3.135		+3.465	V
Supply Current	I_CC			450	mA
Power Dissipation	P_D			1.5	W

Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.135 to 3.465：

Parameter			Symbol	Min	Typ	Max	Unit	Note
Transmitter:
Differential input voltage swing				180		700	mVpp	1
Transmit Disable Input		H	V_IH	2.0		Vcc+0.3	V
Transmit Disable Input		L	V_IL	0		0.8	V
Transmit Enable Output		H	V_OH	2.4		Vcc+0.3	V
Transmit Enable Output		L	V_OL	0		0.4	V	2
Input Differential Impedance			Zin	80	100	120	Ω
Receiver
Differential output voltage swing				300		850	mVpp	3
LOS Output	H		V_OH	2.4		Vcc+0.3	V	2
LOS Output	L		V_OL	0		0.4	V
Output Differential Impedance			Zon	80	100	120	Ω

Notes:

Note 1) TD+/- are internally AC coupled with 100Ω differential termination inside the module.

Note 2) Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V.

Note 3) RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user SERDES.

Optical Parameters(TOP = 0 to 70°C, VCC = 3.135 to 3.465 ：

Parameter			Symbol	Min	Typ	Max	Unit	Ref.
Transmitter
Bit Rate			BR	9.9		11.3	Gb/s
Optical Wavelength	JHA5920D-2733		λ	1260	1270	1280	nm
Optical Wavelength	JHA5920D-3327			1320	1330	1340	nm
Average output power			Po	-3		+2	dBm
Optical Extinction Ratio			ER	3.5			dB
Spectral width			Δλ			1	nm
Side Mode Suppression Ratio			SMSR	30			dB
Optical Eye Mask				Compliant with IEEE802.3ae
Receiver
Bit Rate			BR	9.9		11.3	Gb/s
Optical Wavelength		JHA5920D-2733	λ	1320	1330	1340	nm
Optical Wavelength		JHA5920D-3327		1260	1270	1280
Receiver Sensitivity			Sen			-14.5	dBm	1
Maximum Input Power			P_MAX	0			dBm
LOS De-Assert			LOS_D			-15	dBm
LOS Assert			LOS_A	-25			dBm
LOS Hysteresis			LOS_H	0.5		4	dB

Notes:

Note 1) Measured with a PRBS of 2³¹-1 at 1 x 10^-12 BER and 3.5 dB extinction ratio.

Pin Assignment：

Diagram of Host Board Connector Block Pin Numbers and Name

Pin Function Definitions：

PIN #	Name	Function	Notes
1	VeeT	Module transmitter ground	1
2	Tx Fault	Module transmitter fault	2
3	Tx Disable	Transmitter Disable; Turns off transmitter laser output	3
4	SDL	2 wire serial interface data input/output (SDA)
5	SCL	2 wire serial interface clock input (SCL)
6	MOD-ABS	Module Absent, connect to VeeR or VeeT in the module	2
7	RS0	Rate select0, optionally control SFP+ receiver. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s
8	LOS	Receiver Loss of Signal Indication	4
9	RS1	Rate select0, optionally control SFP+ transmitter. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s
10	VeeR	Module receiver ground	1
11	VeeR	Module receiver ground	1
12	RD-	Receiver inverted data out put
13	RD+	Receiver non-inverted data out put
14	VeeR	Module receiver ground	1
15	VccR	Module receiver 3.3V supply
16	VccT	Module transmitter 3.3V supply
17	VeeT	Module transmitter ground	1
18	TD+	Transmitter inverted data out put
19	TD-	Transmitter non-inverted data out put
20	VeeT	Module transmitter ground	1

PIN #	Name	Function	Notes
1	VeeT	Module transmitter ground	1
2	Tx Fault	Module transmitter fault	2
3	Tx Disable	Transmitter Disable; Turns off transmitter laser output	3
4	SDL	2 wire serial interface data input/output (SDA)
5	SCL	2 wire serial interface clock input (SCL)
6	MOD-ABS	Module Absent, connect to VeeR or VeeT in the module	2
7	RS0	Rate select0, optionally control SFP+ receiver. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s
8	LOS	Receiver Loss of Signal Indication	4
9	RS1	Rate select0, optionally control SFP+ transmitter. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s
10	VeeR	Module receiver ground	1
11	VeeR	Module receiver ground	1
12	RD-	Receiver inverted data out put
13	RD+	Receiver non-inverted data out put
14	VeeR	Module receiver ground	1
15	VccR	Module receiver 3.3V supply
16	VccT	Module transmitter 3.3V supply
17	VeeT	Module transmitter ground	1
18	TD+	Transmitter inverted data out put
19	TD-	Transmitter non-inverted data out put
20	VeeT	Module transmitter ground	1

Note 1) The module ground pins shall be isolated from the module case.
Note 2) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.
Note 3) This pin shall be pulled up with 4.7K-10Kohms to VccT in the module.
Note 4) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.

SFP Module EEPROM Information and Management:

The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I²C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.

Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)

Table 2 - EEPROM Serial ID Memory Contents (A0h)

Data Address	Length (Byte)	Name of Length	Description and Contents
Base ID Fields
0	1	Identifier	Type of Serial transceiver (03h=SFP)
1	1	Reserved	Extended identifier of type serial transceiver (04h)
2	1	Connector	Code of optical connector type (07=LC)
3-10	8	Transceiver	10G Base-LR
11	1	Encoding	64B/66B
12	1	BR, Nominal	Nominal baud rate, unit of 100Mbps
13-14	2	Reserved	(0000h)
15	1	Length(9um)	Link length supported for 9/125um fiber, units of 100m
16	1	Length(50um)	Link length supported for 50/125um fiber, units of 10m
17	1	Length(62.5um)	Link length supported for 62.5/125um fiber, units of 10m
18	1	Length(Copper)	Link length supported for copper, units of meters
19	1	Reserved
20-35	16	Vendor Name	SFP vendor name: XAT
36	1	Reserved
37-39	3	Vendor OUI	SFP transceiver vendor OUI ID
40-55	16	Vendor PN	Part Number: “XAT-WW20-1270” or “XAT-WW20-1330” (ASCII)
56-59	4	Vendor rev	Revision level for part number
60-62	3	Reserved
63	1	CCID	Least significant byte of sum of data in address 0-62
Extended ID Fields
64-65	2	Option	Indicates which optical SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported)
66	1	BR, max	Upper bit rate margin, units of %
67	1	BR, min	Lower bit rate margin, units of %
68-83	16	Vendor SN	Serial number (ASCII)
84-91	8	Date code	XAT’s Manufacturing date code
92-94	3	Reserved
95	1	CCEX	Check code for the extended ID Fields (addresses 64 to 94)
Vendor Specific ID Fields
96-127	32	Readable	XAT specific date, read only
128-255	128	Reserved	Reserved for SFF-8079

Digital Diagnostic Monitor Characteristics:

Data Address	Parameter	Accuracy	Unit
96-97	Transceiver Internal Temperature	±3.0	°C
98-99	VCC3 Internal Supply Voltage	±3.0	%
100-101	Laser Bias Current	±10	%
102-103	Tx Output Power	±3.0	dB
104-105	Rx Input Power	±3.0	dB

Regulatory Compliance:

The XAT-WW20-127/133 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following).

Electrostatic Discharge

(ESD) to the Electrical Pins

MIL-STD-883E

Method 3015.7

Class 1(>1000 V)

Electrostatic Discharge (ESD)

to the Single LC Receptacle

IEC 61000-4-2

GR-1089-CORE

Compatible with standards

Electromagnetic

Interference (EMI)